Audio Technica Freeway 200 VHF Headset Wireless SystemThe Audio-Technica’s Freeway 200 Series Wireless Systems are designed to provide reliable performance, easy setup and clear, natural sound quality.
Each 200 Series professional VHF wireless headset system includes a receiver, a body-pack transmitter and headset microphone on a specific crystal-controlled frequency. A novel dipole antenna system on the receiver improves operation by providing a ground element in addition to the usual signal element.
Audio-Technica 200 Series Features
- Easy operation and clear, natural sound quality
- Reliable performance and durable construction
- Advanced dipole antenna system for extended operating range
- Power, RF, and AF Peak indicators
- Volume control, 1/4 inch output jack and space-saving power supply
- Rugged unidirectional dynamic element on handheld microphone/transmitter
- Variable microphone trim control and easily accessible On/Standby/Off switch on transmitters
- Professional locking connector on UniPak body-pack transmitter
- Available in 5 system configurations
The ATW251H headset system in the Freeway 200 series by AudioTechnica is available with either the PRO 8HEcW or the PRO 92cW (black or beige) headset microphone. All headset systems include the ATW-R250 receiver, ATW-T201 transmitter and your choice of headset microphone.
Multiple wireless units? Leading the industry again, AMS lets you choose your wireless frequency!
Channel Frequencies
- 169.505 MHz
- 170.245 MHz
- 171.905 MHz MHz
RECEIVER SPECIFICATIONS
- Receiving System Non-diversity, single-channel, dual antenna system
- Image Rejection 50 dB minimum
- Signal-to-noise Ratio 80 dB at 10 kHz deviation (IEC-weighted), maximum modulation 15 kHz
- Total Harmonic Distortion <=1% (10 kHz deviation at 1 kHz)
- Sensitivity 20 dBµV for 60 dB S/N (IEC-weighted)
- Audio Output 350 mV (1 kHz modulation, 10 kHz deviation, 100 k ohm load)
- Output Connector 1/4" TS ("mono") phone jack
- Power Supply 100-240V AC (50/60 Hz) to 12V DC 1A (center positive) switched mode external power supply
- Dimensions 7.48" (190.0 mm) W x
1.65" (42.0 mm) H x
5.12" (130.0 mm) D
--
- Net Weight 11.0 oz (311 g)
- Accessory Included Power supply
BODY-PACK TRANSMITTER SPECIFICATIONS
- RF Power Output 10 mW High position, 2 mW Low position, typical
- Spurious Emissions Under federal regulations
- Dynamic Range >=90 dB, A-weighted
- Input Connections High impedance, low impedance, bias
- Battery 9V (NEDA type 1604) alkaline, not included
- Current Consumption 30 mA typical
- Battery Life Approximately 15 hours in High position;
Approximately 20 hours in Low position
(depending on battery type and use pattern)
- Dimensions 2.56" (65.0 mm) W x
4.33" (110.0 mm) H x
1.00" (25.4 mm) D
- Net Weight 2.8 oz (78 g) (without battery)
HANDHELD TRANSMITTER SPECIFICATIONS
- RF Power Output 10 mW High position, 2 mW Low position, typical
- Spurious Emissions Under federal regulations
- Dynamic Range >=90 dB, A-weighted
- Microphone Element Dynamic unidirectional
- Battery 9V (NEDA type 1604) alkaline, not included
- Current Consumption 30 mA typical
- Battery Life Approximately 15 hours in High position;
Approximately 20 hours in Low position
(depending on battery type and use pattern)
- Dimensions 9.50" (241.3 mm) long,
2.10" (53.3 mm) maximum diameter
- Net Weight 12.7 oz (360 g) (without battery)
- Accessory Included AT8456a Quiet-Flex™ stand clamp
