Carl Martin Guitar Tuner Pedal

    Order your Carl Martin Guitar Tuner Pedal and enjoy 0% Interest Payment Plans, Free Shipping, Free Extended Warranty and 45 Day Money Back Guarantee.
    Sorry! This item is no longer available.
    Out of Stock:
    Product Description

    The Carl Martin tuner is simple, attractive, efficient and useable for all types of guitar players! This tuner pedal features a classic die-cast black casing, and is switch-able between standard readout and strobe.  The Carl Martin pedal is bright and clear enough to be read from a standing position. This tuner pedal can be calibrated from 437 through 443 with the default, of course, at A440. This Carl Martin tuner features a mute switch (for silent tuning) and True Bypass on/off for a clean signal path. With this tuner pedal, you have the perfect addition to your Carl Martin pedal collection!

    Carl Martin Tuner Pedal Features:

    • Visible from a standing position
    • Seven LEDs on front panel represent seven different calibrations
    • Calib, Note and Strobe buttons
    • On/Off and Mute switches
    • For all types of guitar players
    • 1/4 Inch Input and Output
    • Powered by 9V battery or an external power supply
    Calib Button
    The seven LEDs on the front of the pedal represent seven different calibrations. Pressing the Calib button, allows scrolling through these settings. The calibration settings of the tuner are from 437Hz to 443Hz with the default value at 440Hz. Disconnecting the power source and then reconnecting will reset the calibration to 440 Hz.

    Note Button
    Press the Note button to cycle the display through 0,A,A#,B,C#,C,,D,D#,E,F,F#,G,G#, for individual or fixed note tuning. The chosen note will blink three times indicating the tuner has entered the fixed note tuning mode. In this mode, the far left LED indicates flat tuning, and the far right LED indicates sharp tuning. The LEDs blink faster to indicate distance from the note, and blink slower as the tuning gets closer. When neither LED is lit, accurate tuning has been achieved. Holding the Note button for 2 seconds and then releasing, will return the display to 0, and will exit the fixed note mode immediately.

    Strobe Button
    The Strobe button selects between Sweep and Strobe mode. The Tuner will remain in the Mode chosen until the alternate has been selected.

    On/Off Switch
    This switch determines whether the pedal is active or bypassed (on/off). This is a True Bypass switch.

    Mute Switch
    This switch will mute the signal when engaged (on), for silent tuning.

    Using a standard line cable with a 1/4 inch jack, you can connect your instrument to this jack.

    DC 9V
    To use external power (not provided) use only a 9-Volt DC adapter. For details please refer to the section POWER REQUIREMENTS.

    Using a standard line cable with a 1/4 inch jack, connect this output to the input of your amplifier or next accessory in the signal chain. This is a True Bypass output. When the tuner is disengaged (off), your signal will travel directly to your amp or effects chain without tonal sacrifice.

    The Battery is located inside the pedal. To install or replace the 9V battery, loosen the screws on the bottom and remove the bottom plate. Be careful not to scratch the unit.
    Always remember to unplug your cables from the pedal to conserve battery life. Some battery drain will take place when the line cables are connected to the tuner, regardless if the tuner is engaged or not.

    Operating Temperature
    Do not expose this unit to excessive heat. This unit is designed to operate between 32F and 104F (0oC and 40oC). This unit may not function properly under extreme temperatures, and should be allowed to return to recommended temperatures before use.

    Power Requirements:
    • Battery: Standard 9V Alkaline battery
    • Power consumption: max. 80 mA
    • Power supply:
      • 9 V DC (regulated), 100 mA minimum
      • 2.1 mm female plug, center negative (-)
    ATTENTION: Please Use DC Power Supply Only!
    Failure to do so may damage the unit and void the warranty.

    Product Specifications
    Carl Martin Tuner Pedal:
    • Precision: +/- 1 cent
    • Frequency range: A0(27.5 Hz)-C8(4186 Hz)
    • Residual Noise: -85 dB
    • Indicators: Calib, Note, Strobe
    • Connectors: INPUT, OUTPUT,DC Adaptor jack
    • Power Supply: DC 9V Adaptor (not included)
    • Current Draw: max. 80 mA (DC 9 V)
    • Dimensions (WxDxH): 4.72 x 3.74 x 2.2 inches, 120 x 95 x 56 mm
    • Weight: 0.94lbs/ 420g

    Helpful Info about the Manufacturer
    Phone:  973-772-3333 Warranty:  1 Year
    Customer Reviews
    Currently there are no discussions available for this item.